loading

32bit ACRO NAZE32_BRUSH Brushed Flight
Control Board for DIY Micro FPV ItemID : 185081830

Our Price
RM 70.00
Shipping
RM 8 by courier to Peninsular Malaysia
RM 12 by courier to Sabah, Labuan
RM 12 by courier to Sarawak
Combine Shipping AllowedCombine Shipping Allowed , Ships 1-3 working days after payment.
Please select option below

X

Quantity
- +
Ship From
Segamat / Johor  
Ship To
Within Malaysia
Views
30
Available Quantity
3
Droneshop
Since 25 Aug 2016

Feedback Score
: 6+
Positive Feedback
: 100.00%
Total Product
: 93
NetPay
Buyer Protection Program
Payments are covered by BPP (Learn More)
Item Specification
  • Report
  • Conditions : New

    Product Description


    32bit ACRO NAZE32_BRUSH Brushed Flight Control Board for DIY Micro FPV

    *Enter set motor_pwm_rate = 1000 in the CLI command line in Cleanflight Configuration software, Press enter and enter save to save the command.

     

    Features:

    1. NAZE32_BRUSH is in the revision on the basis of NAZE32 flight control,it is a 32bit brush controller base on NAZE32 firmware .
    2. The flight control support 1S (4.2V) and 2S (8.4V) power supply, 2S power can bring flying experience more violence.
    3. Independent design of the circuit structure, comes with the pressure reduction technology, whether it is 1S or 2S power input, UART1/2 output 5V, UART3 output 3.3V
    4. With a large current NMOS transistors, operating current of up to 10A or more.
    5. Support for PPM, SBUS, DSM receiver input signal.
    6. With battery voltage detection and buzzer interface.

    Notice:

    Before applying power, pay attention to the battery voltage selection.
    The default shipping is 1S (4.2V); When using 2S, first need to disconnect the short contacts 1S, and then put the two pads on the 2S.
    Prohibit shorted together the three pads at the same time.

    Receiver configuration:

    1. DSM receiver soldered directly to the DSM interface 3.3V, GND, RX2, in CF software configuration UART2 for Serial RX, and change the Receiver mode to RX_SERIAL,and then set up the receiver brand with Spektrum1024 or 2048.
    2. SBUS receiver soldered on UART2 interface.SBUS signal in CF software configuration UART2 for Serial RX,and change the Receiver mode to RX_SERIAL,and then set up the receiver brand with SBUS.
    3. PPM receiver soldered on PPM interface.No need to open RX Serial, just in the CF software to change the Receiver mode for RX_PPM.

    Package included:

    1 x ACRO NAZE32_BRUSHED Flight Control Board





    Questions & Answers   Ask Seller

    Recently Viewed Items


    We accept Netpay, Bank Transfer, Credit Card, Online Banking and Cash Deposit.
    However, we do not recommend using netpay, in any case of need to refund, we will not be able to provide full refund due the 3.5% charges on the transaction.
    Any enquiries can whatapps 0132737573

    Poslaju Courier

    Our cut off time is 1pm. All payment made before 1pm will be shipped on the same day.

    Questions & AnswersDo you have any questions to ask merchant about this product   Ask Seller

    Related Products

    Droneshop' Best Seller

    Droneshop' Items



    You may also be interested in Tag:



    Note : The seller assumes all responsibility for listing this item. Please contact the seller to resolve any questions before or after purchasing the item. Currency is RM (Ringgit Malaysia) unless otherwise noted.
    Back to Top
    lelong class
     
    subscribe
    Copyright © 2016 Interbase Resources Sdn. Bhd. (465435-U). All product names are trademarks of their respective companies.
    Lelong.my is not affiliated with or endorsed by any company listed on this site.
      Follow us : facebook       Our Partner : paypal
    Our Affiliates : Lmall.my | Superbuy.my | Pretty.my