Fully Auto Booster Water Pump System (KA4140IDB35)

Feature available to Store Members

Fully Auto Water Pump System (KA4140IDB35)

• Condition: New

Single phase electric clean water pump is the perfect household electric pump.
As a domestic household pump, it is designed for transfer or moving water from one place to another, This electric garden pump is well designed for home use, sprinkling and watering the garden, irrigation and garden applications etc.

The water pump can be used for pressurization of tap water pipes and apartment water pipes, water supply from the under ground or the open wells, farm field and courtyard irrigation.

The Automatic Water Pump Electronic Controller Built in Check Valve, Pressure Gauge, Water Follow Sensor, Pressure Switch, Pressure Vessel

The Electronic Controller orders the automatic start and stop of the water pump when opening or closing any tap or valve of the system. The controller can keep constant pressure and water flow in the system as long as any tap in the system is open during the pumps operation.

Function:
The product is designed especially for all control operation of automatic water pump. If the particular breakdowns occur, such as water failure, obstruction of the suction pipe etc, the product recognizes the breakdowns and the red light ＂Failure＂ lights up, at the same a stop signal is sent to the pump to prevent damages caused by its working in the absence of water. Rectification of the failures that have caused the blockage, allows the system to be restarted by pressing the＂Restart＂button after fill water at water pump priming port.

The controller can ensure a constant pressure for the water supplying system and thus reduce the water hammer effect inside pipeline during water delivering. The controller also possesses the features of reset after power failure. Its starting flow is about 36-60L/h and is convenient for home application.

Specifications Water Pump:

• Power: 0.5 HP
• Max. Capacity (L/min): 35
• Max. Head (m): 35
• Max. Suction (m): 9
• Speed: 2850 RPM
• Overall Dimension (mm): 320 X 180 X 220
• Inlet/Outlet pipe size: 1" BSP (25mm)
• Packing Dimension: 285x185x150mm
• Weight: 5.4KG
• Power: Single-phase voltage 240V, frequency 50 Hz

Specifications Electronic Controller:

• Rated voltage: AC220V - 240V Frequency: 50/60Hz
• Max current: 10A
• Start pressure setting:1.5bar, 3.0bar
• Max working pressure: 10bar
• Connecting thread: Male BSP 1"
• Grade of protection: IP65
• Size: 230mm (H) x 140mm (W)
• Weight: 1.24KG
• Max working temperature: 60℃
• Special Non Return Valve to avoid surges
• Security System removing the possibility of the machine working without water (It also provides for loss of prime or run dry protection. This means that the pump will stop operate when you run out of tank water)

For easy understand, below 1-5 steps easy guide for installation

1.  Install All the Pipe and Fitting from water source to water pump, and from water pump to discharge pipe (House water pipe line), Refer as Picture
2. Fill-up the water at "Water Priming Fill Port" (For First Time install / One day no water supply from source)
3. Connect the Power Supply, Motor to Controller, Controller to Power Supply and connect the ground (Earth) wire at plate screw (Ready)
4. Switch "ON" Controller indicate the pump has started when the green light “Power on” lights up after connecting the power. When the yellow light “Pump on” lights up, it indicates the pump has been started. The pump continues to operate for a few minutes enabling the system to fill in the pipes and to reach the required pressure. If this lapse is insufficient, the red light “Failure” will light up. In this event, keep the “Restart” button pressed and wait, with a tap opened till the red light is off. Once released the button and closed the tap, this Auto Pump Control Switch will keep the pump at its maximum pressure.
5. OK, Now water pump automatic start and stop when opening or closing any faucet or valve of the system

Please Note: If you don't know how to install, Please ask expert plumbing to install and we're not responsible teach you and find a plumbing install for you.

Shipment & Handling Fee to MALAYSIA

Please Note: Delivery to Sabah and Sarawak Delivery Transit Time is 4-8 Weeks

West Malaysia

• Example: Order A + B + C + ... + RM 5.00 Shipment = Total Amount you pay

East Malaysia

• Example: Order A + B + C + ... + Shipment (Order which is Highest Shipment Fee) = Total Amount you pay

LEEQVIUFVHUFVHJFH5.5KGQCHCDHGDCLYA