loading


32bit ACRO NAZE32_BRUSH Brushed Flight Control Board for DIY Micro FPV

RM 70.00
Shipping
From Segamat / Johor , Estimated Arrival 1-3 working days.  
  • RM 8 by courier to Peninsular Malaysia
  • RM 12 by courier to Sabah, Labuan
  • RM 12 by courier to Sarawak
Every subsequent item add RM 0.00 
Please select option below

X

Quantity
- +
*Quantity exceeds maximum allowed
Notify me when it is available again
ItemID
185081830
Ship To
Within Malaysia   
Views
191
Available Quantity
0
Seller Information
Droneshop
Store since 25 Aug 2016

Feedback Score
: 53+
Positive Feedback
: 100.00%
Total Product
: 207
Full Refund if you don't receive your order*
Item Specification
  • Report
  • Conditions : New

    Product Description


    32bit ACRO NAZE32_BRUSH Brushed Flight Control Board for DIY Micro FPV

    *Enter set motor_pwm_rate = 1000 in the CLI command line in Cleanflight Configuration software, Press enter and enter save to save the command.

     

    Features:

    1. NAZE32_BRUSH is in the revision on the basis of NAZE32 flight control,it is a 32bit brush controller base on NAZE32 firmware .
    2. The flight control support 1S (4.2V) and 2S (8.4V) power supply, 2S power can bring flying experience more violence.
    3. Independent design of the circuit structure, comes with the pressure reduction technology, whether it is 1S or 2S power input, UART1/2 output 5V, UART3 output 3.3V
    4. With a large current NMOS transistors, operating current of up to 10A or more.
    5. Support for PPM, SBUS, DSM receiver input signal.
    6. With battery voltage detection and buzzer interface.

    Notice:

    Before applying power, pay attention to the battery voltage selection.
    The default shipping is 1S (4.2V); When using 2S, first need to disconnect the short contacts 1S, and then put the two pads on the 2S.
    Prohibit shorted together the three pads at the same time.

    Receiver configuration:

    1. DSM receiver soldered directly to the DSM interface 3.3V, GND, RX2, in CF software configuration UART2 for Serial RX, and change the Receiver mode to RX_SERIAL,and then set up the receiver brand with Spektrum1024 or 2048.
    2. SBUS receiver soldered on UART2 interface.SBUS signal in CF software configuration UART2 for Serial RX,and change the Receiver mode to RX_SERIAL,and then set up the receiver brand with SBUS.
    3. PPM receiver soldered on PPM interface.No need to open RX Serial, just in the CF software to change the Receiver mode for RX_PPM.

    Package included:

    1 x ACRO NAZE32_BRUSHED Flight Control Board


    Last Updated @ 3/24/2017 9:50:31 AM


      Buy with confidencewe have 83 Good Ratings from buyers !

    BuyerItem IDDateRatings
    cl**** 186946829 1/16/2018 11:28:00 AM Good seller fast delivery
    mo**** 191607131 1/9/2018 5:52:00 PM fast response,item as described, good quality,Will trade again.thank you for the free gift .....
    mo**** 198903448 1/9/2018 5:52:00 PM fast response,item as described, good quality,Will trade again.thank you for the free gift .....
    mo**** 186959215 1/9/2018 5:52:00 PM fast response,item as described, good quality,Will trade again.thank you for the free gift .....
    mo**** 190331903 1/9/2018 5:52:00 PM fast response,item as described, good quality,Will trade again.thank you for the free gift .....
    as**** 198917817 12/28/2017 2:28:00 PM -
    cy**** 185390314 12/20/2017 5:35:00 PM -
    zu**** 196494558 12/12/2017 1:17:00 AM -





    Questions & Answers   Ask Seller


    We accept Netpay, Bank Transfer, Credit Card, Online Banking and Cash Deposit.
    However, we do not recommend using netpay, in any case of need to refund, we will not be able to provide full refund due the 3.5% charges on the transaction.
    Any enquiries can whatapps 0132737573

    Default Courier: Poslaju

    On request (no extra charges): Skynet, DHL, Airpak, Nationwide Express, ABX

    Please pm or leave a remarks if you would like to use other courier

    All orders will be ship next working day.

     

     

    Nobody at home to receive the delivery?

    No worry, you can use pegeon point! Just pick up your delivery from the pgeon point! No extra charges!

    1. Choose your nearst pegeon point from the link below.

    https://www.pgeon.delivery/pgeon-points/

     

    2. Enter the address of the pegeon point starting as the name of the pegeon point as your delivery address

    For example:

    99 speedmart Permai Square 1328

    No: 1 and 3jalan Bpp 5/7pusat Bandar Putra Permai Seri Kembangan 43300 Malaysia

     

    3. REMEMBER to leave a remark: pgeon point drop off on your order!

    4. Done, check the tracking number for the status of the delivery, once it arrived, you can go and collect your item at your selected pgeon point any time within the operating hour!

    PM us if you are not clear about the steps!

    Questions & AnswersDo you have any questions to ask merchant about this product   Ask Seller

    0.0

    0.0 stars out of 5
    5 star
    0
    4 star
    0
    3 star
    0
    2 star
    0
    1 star
    0
    Share your thoughts with others
    Write a review
    Only buyers who purchased the product may leave a review

    Frequently Bought Together

    Customers Who Bought This Item Also Bought

    Related Products

    Recently Viewed Items

    Droneshop' Best Seller

    Promotion Items

    Droneshop' Items



    You may also be interested in Tag:



    Note : The seller assumes all responsibility for listing this item. Please contact the seller to resolve any questions before or after purchasing the item. Currency is RM (Ringgit Malaysia) unless otherwise noted.
    Back to Top
    Our Affiliates : Lmall.my | Superbuy.my | Pretty.my