AC220V power lightning protector Product introduction: For ac/dc lightning protection of secondary distribution equipment such as infrared correlation alarm program-controlled switches such as security monitoring system the product appearance easy installation and wiring simple maintenance can long-term stability under the bad environment. The product series installed on the front end of the ac/dc power distribution equipment to prevent lightning or surge of factors such as induced over-voltage over-current phenomenon on the system or equipment damage. Function characteristics: 1, stable performance, small residual pressure, fast response time, long life; 2, with multi-stage discharge, filtering, clamping the overvoltage and overcurrent can effectively restrain; 3, large discharge current (10 ka mu s 8/20), fast response time (ns) 25 or less 4, integration, small volume, simple wiring, installation is convenient. Technical parameters: Nominal voltage Un 120V-/ ~ 230V-/ ~
The maximum continuous operating voltage Uc 212V-/150V ~ 360V-/255V ~
Nominal current In 16A 16A
Nominal discharge current (8/20) Isn 10kA 10kA
Voltage protection level Up 650V 1kV
Limit voltage (8/20μs) 20KA ≤ 800V
Installation and construction:
1, connected in series, "output" are connected equipment to be protected, to be installed in the front of the device to be protected.
2, to regularly check mine, please change occurs when the deterioration of the product, in order to avoid your unnecessary losses.
3, Lightning input terminal IN connected with the signal path, connected to the output terminal OUT and the equipment to be protected and can not be reversed.
4, the shall be grounded, be sure to be well grounded and grounding wire resistance must not be greater than 4 ohms straight. , Remember not live operations, construction should be checked after the closing run mine without exception.
5, the product requires no special maintenance work when the system fails suspected mine, the mine can be removed, and then through a series of checks on the signal, if restored to the state before using the system back to normal, then the anti-Ray is damaged and must be replaced immediately.
Note:
1) Input (IN) on mine, output (OUT) mark, the output terminal is connected with the equipment to be protected, not reversed. Otherwise it will cause damage to mine equipment can not be protected. When installed at both ends of the line must be laid separately, can not be tied together to prevent secondary induction phenomenon.
2) If due to the poor connection plugs and sockets and other factors caused the loss increases, should reconnect or replace mine.
3) Users can not disassemble the various parts of the mine fasteners, to avoid damage, affecting the normal operation.
Last Updated @ 1/20/2018 9:43:04 AM |
Note:
-Netpay is own by Lelong.com.my and will charge extra 2.5-3.5% on every transaction. We recommeded buyer to click on other payment method then pay direct to seller. Doing this way will save you 2.5-3.53% of netpay transaction charges and in case of out of stock will get full refund and dont need to wait around 2 week for NETPAY refund.
-No need to send us any email or sms after payment. Just remember to update your buynow order.
-For bulk order or quantity order can place order first and send us a pm to ask for best price.
SKIPPING NETPAY CHARGES (updated as of 20 JAN 2018)
Friendly reminder for those to avoid paying "NetPay" (2.5-3.5%) or preferably direct "Funds Transfer" (0%), please transfer your payment to one of our bank accounts above.
Once the transfer is done, kindly notify us by uploading the bank receipt to your order, we will then proceed your shipment once the payment has been verified.
NOTE:
a. Lelong charges extra 2.5-3.5% service fee of the total sales amount for every NetPay transaction, we recommend buyer to use Internet Banking (direct funds transfer), or Cash Deposit Machine to avoid charges.
b. PayPal charges up to 3.9% (local buyer) / up to 5% (oversea buyer) for service fees.
c. Payment clearance for cheque may take up 2 to 3 working days
d. Payment from third party bank may take up 1 to 2 working days
NetPay (via Credit card/Debit card)
· P/S: If you pay using Credit Card via netpay, all out of stock item will not be fully refund because Netpay has charge 3.5%
example:
You have paid RM100. RM100 – 3.5% = RM96.50 will be refund only.
Note:
-Netpay is own by Lelong.com.my and will charge extra 2.5-3.5% on every transaction. We recommeded buyer to click on other payment method then pay direct to seller. Doing this way will save you 2.5-3.53% of netpay transaction charges and in case of out of stock will get full refund and dont need to wait around 2 week for NETPAY refund.
-No need to send us any email or sms after payment. Just remember to update your buynow order.
-For bulk order or quantity order can place order first and send us a pm to ask for best price.
SKIPPING NETPAY CHARGES (updated as of 20 JAN 2018)
Friendly reminder for those to avoid paying "NetPay" (2.5-3.5%) or preferably direct "Funds Transfer" (0%), please transfer your payment to one of our bank accounts above.
Once the transfer is done, kindly notify us by uploading the bank receipt to your order, we will then proceed your shipment once the payment has been verified.
NOTE:
a. Lelong charges extra 2.5-3.5% service fee of the total sales amount for every NetPay transaction, we recommend buyer to use Internet Banking (direct funds transfer), or Cash Deposit Machine to avoid charges.
b. PayPal charges up to 3.9% (local buyer) / up to 5% (oversea buyer) for service fees.
c. Payment clearance for cheque may take up 2 to 3 working days
d. Payment from third party bank may take up 1 to 2 working days
NetPay (via Credit card/Debit card)
· P/S: If you pay using Credit Card via netpay, all out of stock item will not be fully refund because Netpay has charge 3.5%
example:
You have paid RM100. RM100 – 3.5% = RM96.50 will be refund only.
5 star |
|
0 |
4 star |
|
0 |
3 star |
|
0 |
2 star |
|
0 |
1 star |
|
0 |