Home automation is "The Internet of Things". The way that all of our devices and appliances will be networked together to provide us with a seamless control over all aspects of our home and more.
Sonoff is a low-cost, affordable device that help you to step into the amazing smart home. It is a WiFi wireless switch that can connect to appliance of different types and brands.
Sonoff sends data to cloud platform through the WiFi Router, which enables you to remotely control all appliances
with the App eWeLink on your smart phone. The server of Sonoff is Amazon AWS global server.
Sonoff makes all your home appliances smart, as long as your phone has network you can remotely turn on or turn off your appliances from anywhere at any time. And by setting timing schedules for your appliances, you can maintain a carefree life.
As long as your smart phone has 2G/3G/4G/WiFi network, you can control all your home appliances in your smartphone no matter where you are and at any time.
This is used for DIY smart home, you can connect this item with your electronic devices, so that devices will be controlled in your smartphone, such as lights, pumps, water-heater, fans.... . So, just enjoy smart home by your DIY.
Maximum power: 2200W
Rate Voltage: AC 90-250V
Power Adapter: Without Power Adapter
Transmission mode: Wi-Fi communication
Control mode: Mobile APP;
Transmission mode: Wi-Fi communication;
Controlled lines: 1;
Platform: Android, iOS;
Working temperature: 0-55 degree
Functions: Remote switch On/Off, Daily Timer, Countdown timer, Loop timer, Logic Scene creation (Create program to logically control multiple switches like programmable logic controller, PLC).
To install Sonoff, pay attention to the IN and Out mark on Sonoff.
Switch off electricity source
Open the two shells at both ends
Connect the two electricity source cables(Live and Neutral) to the 2 ports with "IN" mark, one cable for one port and there's no limitation for which port to connect.
Connect the two appliance cables(Live and Neutral) to the 2 ports with "OUT" mark, one cable for one port, and there's no limitation for which port to connect
Cover the shells and screw firmly
Pair with 433MHz RF remote controller without WiFi
If the Sonoff and Slampher you buy has 433MHz RF receiver inside, then you can pair them with the RF Remote controller. The way to do that is explained below:
Quickly press "SET" button on Sonoff and Slampher twice, the red LED on Sonoff/Slampher will flash one time, then press one of the ABCD buttons on the controller once for a few seconds for pairing. If you pair it with A, then you can press A to turn on/off your device.
To cancel the pairing, you need to fast press the"SET" button on Sonoff/Slampher 3 times. If you short press the “SET” button, it will become a switch button, with it you can turn connected appliances on or off.
The APP E-WeLink supports all ITEAD smart home products and cooperated products which include: Sonoff, Sonoff RF, Sonoff TH, Sonoff SV, Slampher, Smart Socket, smart fan(sold in China), dimming led(sold in China),etc.
E-WeLink supports multiple languages: Simplified Chinese, Traditional Chinese, English, Russian, Polish, French, Danish, and Italian. More languages will be supported in the near future. Currently, the APP supports below functions:
Remote turn on/off
We are developing it to support more functions in the near future. So far, the application supports single channel smart switch, double channel smart switch, multi-channel smart switch, smart fan, dimming led, Sonoff TH temperature and humidity smart switch.
1.Download the APP to your smart phone or tablet
Download the Android version APP from here.
Or search eWeLink on Google Play.
Scan below QR Code to download eWeLink.
2.Install the APP to your smart phone
3.Register a new account
You`ll need to enter your phone number/email address and a password(at least 8 characters). Enter SMS verification code to register.Updates: Users from Asian countries MUST register with mobile phone number. While users outside Asian area MUST register with email address.
4.Login with your account.
Android Version eWeLink:
1) For Android version, you must switch on the WiFi on your phone before adding device.
2)Long press the “SET” button(pairing button) on Sonoff/Slampher/Smart Socket/Sonoff RF until the green LED indicator fast blinks(you can use your finger to press directly).
3)Click the search icon in the middle. Check out the blinking way and select corresponding adding way, then click"next".
4)Select your WiFi account and enter password(If no password, keep it blank), click remember so that next time you don’t need to fill in again, click"next".
5)Then it will auto-search and connect the “ITEAD-100000xxxxx” device around you.
6)Name your device,access the device and control it.
iOS Version eWeLink:
1)Click the search icon in the middle.
2)Long press the ''SET'' button(pairing button) on Sonoff/Slampher/Smart Socket/Sonoff RF until the green LED indicator fast blinks. Check out the blinking way and select corresponding adding way, click"next".
3)If your device belongs to 2nd generation (led indicator flash 3 times and repeat), then open phone Setting>WiFi>connect the WiFi beginning with ITEAD, enter default password 12345678.
4)Go back to the App to confirm.
5)Then enter your WiFi router SSID and password.(If no password, keep it blank)
6)Finally, name your device and submit.
NOTE: If you see the new added device is offline, please wait for a few seconds. If it stays offline, please restart the device, if everything is ok, it will become online on the App.
If you use use WiFi A to add the device, when switch to WiFi B, you will unable to control the device. To make the device work with WiFi B, you need to delete it add it over WiFi B.
One device has one owner. If you have successfully added a device to your account, you cannot add this device to another account unless you delete it from account from the first account. Only the owner of the device can share it to other accounts.
Green LED indicator meanings（for all ITEAD smart home devices）
1. There are two kinds of led flash ways when in pairing state (for smart devices of 1st generation and 2nd generation respectively). For devices of 1st generation, during adding process, iOS users need to go to Setting–>Wi-Fi, and connect the WiFi starts with ITEAD-******* with the password 12345678. While android users do not need to set this.
Device in pairing Mode for 1st generation: green led fast blinks, as shown below:
Device in pairing mode for 2nd generation: green led fast blinking or blinks 3 times and on repeatedly means in pairing state, as shown below:
2.Green led keeps on means device has connect to server successfully, as shown below:
3.Green led quickly blinks one time and repeats, which means device failed to connect to router. In this case, please confirm your wifi name and password is correct and try to pair again, as shown below:
4.Green led slowly blinks means device has connected to router and server, but failed to be added in device list. Try to add the device again. As shown below:
5.Green led quickly blinks twice and repeats, this means the device has connected to router but failed to connect to server. Please confirm your WiFi router works normally. As shown below:
To delete a device, you need to go to the devices list, tap delete icon to delete it. Or access to the device you want to delete, you'll see the "Delete"button on the upper-right corner.
7.Manage Group,Scene, Smart Scene
Enter the device list page "All Devices", click to expand it, you will see all your groups. Tap on the "Manage Group" to create new group.
Tap on the upper-right corner of "All Devices" page, you will see "scene", click on it to manage your scene.
You can specify your device into different group, this helps easily manage a huge quantity of devices. For example, you can create a new group called: Kitchen. Specify all those devices installed in kitchen to this group, next time when you leave the kitchen, you can just enter into the group”Kitchen” page to turn off all devices.
Enter a group, you can remove or add more device. If you delete a group, the devices belong to this group will still exist in “My device” list.
A scene contains many devices, set each device status to be Close(off), Open(on) or Keep(keep current status), then save it. All devices will be automatically executed to the preset status.
So you can use the scene to specify different LEDs to scene A, set them on or off or keep, save them. Next time, the system will auto execute the scene.
You can set smart scene- use a trigger device to collect environment data to trigger ON/OFF other devices. So far, the smart scene trigger devices we provided includes: Sonoff TH10/TH16, Sonoff SC, more supported devices will come soon. And the smart devices can be triggered ON/OFF includes all itead 1-channel switches/sockets. If you want to know whether our smart home products support this function or not, please inquire our customer service while placing the order.
How does a smart scene work? Take Sonoff TH10 for example.
Firstly, set Sonoff TH10 in manual mode, only when it trigger the condition can the task be executed. Then set smart scene condition: Sonoff TH10≥27℃, execute Open Sonoff. If your Sonoff TH real temperature is 26℃, when it become 27℃ or higher, Sonoff will be auto-turned on. But if your original real time temperature is higher than 27℃, it cannot trigger the condition and turn on Sonoff.
To sum up, to use the smart scene of Sonoff TH, you need to:
1. Have at least one Sonoff TH and one 1-channel switch/socket(Sonoff, Sonoff RF, Sonoff SV, Smart Socket, etc.).
2. All above devices should be added in the same account, you are the owner of the devices. Shared devices are not supported.
3. Sonoff TH is in manual mode, not auto mode.
4. Real time temperature should across the preset temperature to trigger the condition.
Enter the device you want to share, tap on icon "Share" then enter the Phone number/email address (register and login first, stay online) you want to share with. Then he/she will receive an invitation message, by accepting the invitation, he/she will have the authority to control the device you share. Only the owner of the devices has right to share devices.
Itead is improving the App UI design. We keep upgrading the App for that. Many people care about CE certification very much, Itead has got some smart devices passed the CE test and got the certificate. Please check out from our Wiki. Most people may worry about is the server. What Itead smart home series use is Amazon AWS Global Server, which is stable and easy to be accessed. We have a team to back up our smart home products and we'll make them better and better.
1 x DIY WiFi Remote Switch Module
Let's watch the video to see how it brings us more convenient!